How To Repair Hp Monitor

Introduction

If unsure whether your calculator is off or in hibernation, turn it on, and so close downwards through the operating system.

Disconnect all external devices, plug-ins and power from the computer.

• Locate the battery on the bottom side of the laptop.

• Slide the release switch and the battery will pop out.

• Remove the battery



• Using a Philips #1 Loosen the three 7mm convict screws that secure the memory module compartment cover to the reckoner.

• Lift the rear edge of the cover, swing it upwards and to the front, and remove the cover.

• Loosen the two 6mm captive screws that secure the hard drive port bezel cover to the calculator, using a Philips #1.

• Lift the correct side of the hard drive port bezel cover, swing it up and to the left, and remove the cover.

• Utilize the Mylar tab to lift the difficult drive up, and so slide it to the left to release it from the hard drive bay.

• Disconnect the hard bulldoze cablevision from the organisation board.

• Remove the hard drive from the hard drive bay and set it aside.

• With laptop upside down locate the three sets of screws that fasten the keyboard and switch comprehend.

• Two Phillips 7mm screws that secure the switch embrace to the computer.

• Four Phillips 4.0mm screws that secure the switch cover to the computer. (these are inside the battery bay)

• Four Philips 7mm screws that secure the keyboard to the computer.

• Remove all x screws.

• Turn the estimator over, and locate the Switch Cover.

• Using the Safe Pry Tool, un-clip the Switch Cover until it detaches from the computer.

• The clips volition need conscientious prying to unhook.

• Slide the Switch Cover onto the LCD Monitor, exposing the Speaker Assembly.

• There are two ribbon cables still fastened to the speaker associates

• Detach the two ribbon cables from the speaker assembly.

• Remove the three silver Phillips 3.5mm screws that secure the keyboard to the computer.

• Lift the rear edge of the keyboard and slide the keyboard back until the keyboard connector on the system board is accessible.

• Unhinge the zero insertion force (ZIF) connector to release the ribbon cablevision then pull gently on the cable to release.

• You lot need to unhinge the blue plastic to release the ribbon cable from the main lath.

• The keyboard can now exist lifted off and fix aside.

• Remove the 3mm spiral that secures the WLAN module to the calculator. (The border of the module opposite the slot rises away from the computer.)

• Remove the WLAN module past pulling it away from the slot at an bending.

• Disconnect the two WLAN antenna cables from the WLAN module.

• Disconnect the display panel cable by use pulling upward on cable tabs.

• Disconnect the webcam/microphone cable from the system board.

• Remove the WLAN antenna cables and the webcam/ microphone cable from the clips congenital into the top cover.

• Remove the 4 Phillips 7mm screws that secure the display assembly to the computer.

• Lift the brandish assembly direct up and remove it.

• Remove the ii Phillips 5mm screws that secure the brandish swivel to the display panel.

• The screws are behind plastic stickers and are very easy to bend.

• Use a prying tool to flex the plastic around the monitor display to release the clips holding the display case together.

• Use caution when using prying tool and avoid damaging bezel clips.

• Remove the brandish bezel to uncover the LCD display

• Remove eight screws that fasten the LCD display.

• two Phillips PM2.five×5.0 screws from the top corners.

• half-dozen Phillips M2.five×5.0 screws from the display hinges

• Flex the bottom of the display console and release the brandish hinges

• Place the LCD Monitor side by side to the brandish panel by flipping it over the display hinges.

• Disconnect the display LED cable from the display panel cable and remove the display panel.

• Using the Philips #1, Remove iv 7mm screws from the LCD Monitor frame.

• There are two screws on each side of the LCD Monitor.

• Remove the LCD Monitor from the frame.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Squad

Embed this guide

Choose a size and copy the lawmaking below to embed this guide equally a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/HP+Pavilion+dv6-2158nr+LCD+Monitor+Replacement/21899

Share this post